Well here's a layout for the made over Tube Reamer...
Just did it quickly today.... as yet untested.
Let me know how it goes....enjoy, :D
(http://i2.photobucket.com/albums/y16/stm88/tubereamerv2.png)
Here's the schem.... would someone care to give it a visual run-through?
http://www.runoffgroove.com/tubereamer.html (http://www.runoffgroove.com/tubereamer.html)
What no interest? NO Replies? I did this to put in....
Where's the community spirit guys?
I'll chime in! :)
I've just eyeballed it and it looks good to me.
What does adding C7 and C8 do?
Andy
Andy,
It looks like C7 and C9 are power supply filtering caps. They get rid of some unwanted noise coming in from your power supply.
Scott
Hey nice to hear from you guys.. ;D
I posted this yesterday (my time) and I was wondering....
Yep, power filtering caps.
Thanks for giving it a read through... it's easy to miss something when you've been staring at the same page for a few hours.
The layout looks 'tight', I see no easy way to make it smaller, all the parts seem nicely spaced.
thanks for the info, Toney and Scott, thought they were but wasn't sure.
Would like to have a go at it sometime. Add it to the list.... :)
Cheers Andy
Nice job...what do you use to make these? Paint?
And how long does it take to make a layout this size?
I tried once, it took ages and then I gave up.
Yep, just good old paint and these tools from the gallery...http://aronnelson.com/gallery/Richard-Boop-RLBJR65/Verotools (http://aronnelson.com/gallery/Richard-Boop-RLBJR65/Verotools)
Time taken varies, sometimes i just belt them out in one go...several hours...others I chip away at.
I've got a big one for the Fender Blender in the works that I've been fiddling with for months.
Can any one comment on the placement of R9 in my layout?
Reading the schem, component order would perhaps be better in parallel with C5, before R8 and C9 to ground???
I found it neater in the layout where it is, but to be honest, I'd like someone to confirm the placement is not detrimental.
I built tube reamer version 1 with perfboard from ROG, it sound good. I will try version 2 next time.
thanks
So anyone actually build this ??? ??? ???
Love to hear back a build report.......
I wanna bult it myself shortly
I just got in some vero so I'll try to build it in the next few days and I'll report back on how it goes. Great looking layout!
Hey thanks NB, I'd love to hear back :D
hey toney.. i watch your gallery, i wanna build two things from there, the signal tracer might be good to debug i gues. easy debugging right?
and the jfet matcher..
for the tracer, the spst is to switch between audio wave, and not an audio wave right??
and for fet matcher, no clue how it should be used..
hope u've got some answers :P
thanks a looot
bye bye
DAC
Er thanks...perhaps you got my stuff mixed with someone elses?
I'm sure I've seen those layouts somewhere there...
Anyhow, my stuff is here..all good to go ;D
http://aronnelson.com/gallery/Toneys-Album (http://aronnelson.com/gallery/Toneys-Album)
Toney, great (and ultra-clean) layout as always !!!
I built version 1, however I didn't like it that much, it had a fuzzy edge I didn't like. DIdn't sound like the TS pedals I'm used to. Maybe there were wrong values.
I'll give your layout a try after the Dr, Boogey I'm buiilding. Looks like a fast build.
Thanks Xavier.
Did you try MartyMarts tweaks for the V1?
Definite "winner" with my set up also Torchy had a further variant the Tube Reamer Ultimate- switching diodes, different op amp and a few other tricks. I'm sure Wampcat has the layout.
I built it as per Torchy's schematic with all the bells and whistles ;D
I guess I'm one of those SD1 instead of TS guys, finally I'm using the Wylde OD which is an SD1 variation.
Heh heh...
I still love my beaten up old SD1 more than any TS, AND I just got myself a Wylde OD too....
We must have similar taste.
Toney thanks for another great layout!
Have you tried Bancikas layout software yet? Much quicker and easier than cut and paste.
http://www.storm-software.co.yu/diy/index.php?project=layouts
Quote from: QSQCaito on July 23, 2006, 01:21:30 AM
for the tracer, the spst is to switch between audio wave, and not an audio wave right??
Yes.
Quote from: QSQCaito on July 23, 2006, 01:21:30 AM
and for fet matcher, no clue how it should be used..
R.G. explains it. http://www.geofex.com/Article_Folders/fetmatch/fetmatch.gif
Also try a search.
Richard