Literally just opened it, pretty cool once I figured out just where to place the transistor:
Zero instructions but I did find his website and was able to get this much translated:
http://item.taobao.com/item.htm?spm=a1z10.1.w4004-2018583620.2.ZOF8sF&id=38407360227PCB dimensions: 63*71 mm weight: about 48g
LCR-T4 graphical multifunction testing instrument of resistance + c + diode + SCR + l + +MOS triode tube
12864 LCD LCD with backlight, backlight color is yellowish-green.
Power supply 9V stacked battery. If the power supply for a long time, you can use 2 lithium battery 8.4V battery powered.
Function
* Added power voltage detection function
* Automatic detection of PNP and NPN transistor, n-channel and p-Channel MOSFET, diode (including dual-diode), thyratron tube,Components such as transistors, resistors and capacitors,
* Automatically test the pin of the component, and display on the LCD
* Can detect transistor, MOSFET protection diodes, such as the zoom factor and to determine base-emitter transistor forward biased voltage
* Measure the gate threshold voltage and gate capacitance of the MOSFET
12864 LCD * display LCD (128 * 64 characters)
* Higher testing speed, component tests the validity period: 2 seconds (except in the larger capacitors,Large capacitance measurement also takes a long time, measuring time to 1 minute is normal)
* One-touch operation, power on the test, one-click fix.
* Power consumption shutdown mode: less than 20 nA
* Auto power off function, you can avoid unnecessary waste, saving battery power, improve battery life.
The following features for M8 and M168 Advanced Edition version are different **** please choose according to their needs of *********
1. ATmega8,ATmega168 or ATmega328 microcontroller.
2. 2x16 character liquid crystal display displays the results.
3. One-button operation, automatic power off.
4. Shutdown current 20nA only supporting battery operation.
5. Low cost versions without Crystal, and supports automatic power off. Software version 1.05k when measuring the ATmega168 or ATmega328 without using sleep mode to reduce power consumption.
6. Automatic detection of PNP and NPN bipolar transistor, n and p-Channel MOSFET,JFET, diode dual diode, thyristor SCR.
7. Automatic PIN layout.
8. Measure the current bipolar transistor threshold voltage amplification coefficient and emission knots.
9. Darlington transistors can be a high threshold voltage and high-current amplification factor recognition.
10. For bipolar transistors, MOSFET protection diode testing.
11. Measuring MOSFET threshold voltage and gate capacitance value.
12. Supports two resistance measurements and symbols appear, the highest four-digit digital display and the unit. Display symbol is the tester probes at both ends of the resistance number (1-3). Potentiometer can also be measured. If the potentiometer adjustment to one end and tester cannot distinguish between the middle and the ends of the pins.
13. Resistance measurement resolution of 0.1 ohms, maximum measurement value 50M ohms.
14. A capacitor can be detected and measured. Up to four digits and the units displayed. Values can be from 25pf (8MHz clock 50pF@ 1MHz clock) to 100mF. Resolution up to 1 pF (@ 8MHz clock).
15. For 2UF more than value of capacitor equivalent series resistance (ESR) capacitance measurements. 0.01 ohm resolution and display two-digit numeric value. This feature requires at least Flash 16K ATMEGA (ATmega168 or ATmega328).
16. Two diodes can be shown symbols in the right direction. In addition, the display forward voltage drop.
17. LED testing diode, forward voltage drop is much higher than normal. Two light emitting diode dual diode.
18. Zener diodes can be detected, if the reverse Breakdown voltage is below 4.5V. This will appear as two diodes, can only be determined by voltage. Probe round the diode symbol is the same, in this case, you can use the 700mV real identification of threshold voltage diode anode!
19. This year know that, do not turn the ****
If more than 3 diodes part tests established diode shows the number of failed messages. This will only happen, if the diode is connected to all three probes, and at least one diode. In this case, you should only connect the two probe and start the measurement again, one by one.
20. Measurements of a single diode reverse capacitance value. Bipolar transistor can also be measured, if you connect the base and collector or emitter.
21. Just need a measurement to find out full-bridge connections.
22. Number below 25pf capacitors usually is not detected, or at least in parallel with a diode 25pf capacitors in parallel. In this case, you must subtract the parallel capacitance of the part.
23. Measurement below 2100 Ohm resistance inductor, ATMEGA if you have at least Flash 16K. Range from the 0:01mH over 20H, but accuracy is not good. Survey results show only a single component connections.
24. Testing time is approximately two seconds, only the capacitance and inductance measurement will take a long time.
25. Software before you can set auto power off the measuring frequency.
26. Built-in self test feature check with optional 50Hz signal clock frequency accuracy and waits for the call (the ATmega168 and ATmega328).
27. Optional equipment calibration port output impedance and zero disorder self-test capability of measurements (the ATmega168 and ATmega328). Need a 100nF to 20uF capacitor connected between pin 1 and pin 3 to compensate for offset voltage analog comparator. 40uF capacitor measuring errors can be reduced. Using the same internal calibration of capacitor voltage and reference voltage is found to adjust the internal reference measurement ADC gain.
If the test current exceeds the holding current, thyristor and TRIAC can be detected. But some semiconductor thyristor and TRIAC currents higher than the tester can provide trigger current. Provides the test current is about 6mA! Note that all functionality is used only there are more program memory of the microcontroller as the ATmega168.
